Troubleshoot

I would like my post with the poll removed from Products Chat. The delete function doesn't work. Thanks in advance!

I can't sign in.. map not working properly seams there are bugs everywhere 🙄

I would like to use my Blackbox in Betaflight, but it does not work. I have an SD card in it. I assume that it is a bug.

Hey everyone, I’m hoping someone here might be able to help me troubleshoot an issue I’m having. I recently picked up a Cinelog 20 BNF and am running it with DJI Goggles 2 and the DJI Remote Controller 2. Everything was working fine out of the box, but after my very first crash, I started running into problems. Now, when I try to rebind and rearm the drone, I get a "Remote Control Stick Error" message in the OSD of the DJI FPV Goggles 2. I tried reflashing the flight controller via Betaflight (Comand line with geprc's manufacture profile), but now the board no longer recognizes any stick inputs from my controller when the drone is connected to Betaflight and powered with a battery (throttle stick is all the way down and googles are set to sbus fast). The DJI O3 Air Unit is still transmitting video just fine, so I don’t think that’s the issue. Has anyone run into this before? Is there anything else I can try to fix this? Or does it sound like I may have to replace the flight controller? Any advice would be greatly appreciated! Thanks in advance! https://www.diyfpv.com/post/cm9v1663v000051fpmmsf7p8b?reply=cm9wa9urh0000judmtoix3bjf

Hey all, I'm hoping someone can shed some light on a problem I've been having. First off, I never really paid too much attention when dealing with my 1s whoops. I'd just charge, pull batteries off charger, and go fly till voltage got to where I'd need to land. Never really cared / paid much attention to where that voltage started until recently. So I had a bunch of batteries that were older and were def showing signs of going through too many cycles. However, I noticed when I'd charge them (charger set to 4.35 and they are LiHV BetaFPV regular and lava batteries), my Whoopstor would stop charging at 4.35v. I'd pull the batteries off and when I'd go fly they were reading 4.2v. So I thought maybe it was cause of the age of the battery and they weren't taking a full charge. So I bought myself some new batteries (again BetaFPV 1s lava). Brand new, I'd throw them on my whoopstor v3 and when I'd pull them off and throw them in whoop, I was reading 4.2ish volts in OSD. So I was like, what? So then I took note on my next battery (again, brand new lava 1s) and it read 4.2. So then I used three multimeters and all three (calibrated) read same 4.2ish volts. Even the BetaFPV battery checker read the same as my multimeters. So I begin to think maybe my whoopstor is not charging to 4.35 and the batteries are not the problem. Luckily, I had two other 1s battery chargers. Both set to 4.35. Pull batteries off and instantly go to multimeter. Same...4.2ish volts. So my question, I'm hoping someone can answer, is what the hell? Does BetaFPV lie and these things don't charge to 4.35v. Do I really have three chargers that are lying? Do all of my old batteries, plus 4 brand new ones with 1 cycle on them have something wrong with them? I'm at a loss here. I actually have 6 more 1s batteries coming (not betaFPV but are LiHV) coming. Mainly because I just needed to restock up but I'm genuinely confused about what I'm seeing.

hi so... my old internal 4in1 module died in my tx16s... I ordered a new one... and it arived dead..... am I to asume there is a bit more to it than that? and either something is killing them or this was just a coinsidance EDIT: it's the mainboard 2S rail that's damaged, any ideas?

Hi. I have a Tinyhawk S that suffers from the "random motor not spinning on arming" issue. I've heard the FC is the problem. I was going to buy a Tinyhawk 2 FC but it costs $75 and as I recall, this little guy flew like a brick with 1S and wouldn't land easily with 2s. Can you recommend another FC and frame that I can use with the same motors and camera? Bonus if I can keep the plugs on them. Thanks in advance.

Hey Crew, I really hope you can help, I'm at a loss and really want to get this thing off the ground :) I have a BetaFPV F722 and a Axis Flying Smurf VTX 5.8, connected to a Runcam Pheonix 2 pro Controller https://betafpv.com/products/toothpick-f722-2-6s-aio-brushless-flight-controller-35ablheli_s?variant=40075614126214 VTX https://www.axisflying.com/products/smurfs-vtx-58g-16w-analog-image-transmission?VariantsId=10498 RunCam Pheonix 2 pro https://www.runcam.com/download/Phoenix2/Phoenix_2_Manual.pdf Everything seems to be running fine, however there is not OSD, it is enabled in BF just nothing in the goggles but the camera view... Any ideas?

Hello! I am having trouble with my Acrobee75 BNF from newbeedrone. The video drops out way sooner than it should, and the radio signal is always low. Any suggesstions? Video: https://www.youtube.com/watch?v=PsOf9wpEpvY

Hey Everyone! I am new to Li Ion and would love some input on Landing voltage. I am flying a flik wing with Speedy Bee f405 Wing Mini, Dji o3 air unit and 2s 3000mah Li Ion